-40%

Charge controller 10,000 watt 440 AMP 24 Volt solar panel wind turbine G4-24

$ 33.23

Availability: 81 in stock
  • Item must be returned within: 30 Days
  • Return shipping will be paid by: Seller
  • Application: Agriculture/Farming
  • Condition: New
  • Brand: windmill thermodyne
  • Country/Region of Manufacture: Unknown
  • Restocking Fee: 20%
  • MPN: Wind Turbine Generator
  • Refund will be given as: Money Back
  • All returns accepted: Returns Accepted
  • Model: Wind Turbine Generator T2

    Description

    24 Volt model Battery Controller used to prevent
    batteries and battery banks from over charging.
    DUMP or CUT
    CLICK HERE TO SEE OUR 24V DUMP LOADS
    WIND/SOLAR 24 VOLT 440 AMP  DUMP / DISCONNECT
    CHARGE CONTROLLER
    WITH BUILT IN DIGITAL DISPLAY AND INTELLIGENT
    DUAL PROCESSOR CONTROLLER
    (With Original "THEM" Thermodyne Controller
    . Says THER on the board. Made with real high voltage rated parts.
    Some people claim Thermodyne made but only boards stamped "THER" are genuine Thermodyne boards)
    For solar panels and wind turbines used in battery changing
    IT CAN DISCONNECT THE INCOMING POWER
    OR DIVERT IT
    TO A DUMP LOAD.
    Max solar amperage in divert (dump) mode is 10,000 Watts.  This is a big hybrid wind and solar charge controller.
    Use for wind or solar or both at the same time! Also use for hydroelectric or solar or both.
    User changeable settings -- Several controllers on the market only let you set the dump level!
    Connect multiple turbines and solar panels at the same time!
    Max continuous solar amperage in disconnect mode is 6000 Watts.
    Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source.
    You can connect both wind and solar at the same time. Reverse polarity protection
    Ultra low power consumption even with the volt meter on (almost negligible). You can even set the volt meter to turn off after in-activity.
    On board relay- Isolates electronics from back voltage spikes from large high amp relay.
    This is important to get the longest life out of the electronics. No body else has this!
    Dual (2) Microprocessor controlled -- Extremely  stable and very accurate
    Multiple user changeable settings, and trip points for many various system requirements and applications- You can change the dump point voltage level,
    end of dump voltage level, length of time in divert mode when end dump point voltage is reached
    Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board.
    10,000 watts surge peak max.
    Battery Status digital LED - Lets you know your battery's actual voltage in real time!
    Green LED come on and then you know it's in dump mode or cut mode depending on how your relay lugs wired.
    Plug and Play - Long leads for easy termination to your 24 volt battery or battery bank.
    Battery regulator for both your wind and solar battery input power. This
    regulator can either dump extra power creating free hot water or heat or
    just cut off extra power to keep your batteries from over charging. This
    unit is a must for wind turbine applications as it uses a mechanical
    relay which can handle high voltage surges unlike solid state controllers.
    10,000 WATT Rated
    This controller can CUT-OFF incoming power so NO DUMP LOAD resistor is needed if you do not want to buy one.
    This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions.  This controller was specially developed for wind turbines and works well on solar too - Get just this one battery controller to do it all!
    Worlds Lowest Cost
    Wind & Solar Controller
    Battery Regulator-
    Cut/Disconnect Controller-
    Diversion Load Regulation-
    HOW POWER DRAW DYNAMICS WORKS:
    If you use it as a DIVERSION or DUMP load MODE then it uses almost no power when it is NOT dumping (energy efficient sensing)
    In DISCONNECT mode it draws .2 amps but that's good since that means you have too much power in your batteries anyhow.
    This High Amp unit can control 24 wind turbine batteries or 40 solar panels !
    Used to prevent battery over
    charging on
    Wind - Solar - Hydro
    A battery regulator diverts excess power to power
    some other useful device when ever your battery is full.
    Use the this excess power to make free hot water or to recharge an auxiliary battery bank, so many uses!
    Has push button load tester.
    An extremely robust unit!
    draws almost ZERO power while sensing! 99.998% electrically efficient while sensing!
    Battery regulator.
    Charge regulator.
    Charge controller.
    Dump load regulator.
    "Cut" charge controller.
    Diversion load regulator.
    Micro processor controlled.
    Versatile raised steel mounting plate.
    Measures 10" long by 7" wide by 3" tall.
    Works for all Wind Turbines, Solar panels and Hydro.
    For all voltages ranges in multiple battery banks.
    No grounded IGBT's or MOSFETS - Lighting strike proof isolation.
    CUT -LOAD
    controller (No need to buy a dump load resistor)
    Electrically efficient. Draws only trace power while
    sensing
    !
    Does not waste electricity while
    sensing
    in  diversion load mode!
    HOW POWER DRAW DYNAMICS WORKS:
    If you use it as a DIVERSION or DUMP load MODE then it uses no power when it is NOT dumping (energy
    efficient
    sensing)
    The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over charging. Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing cloths or dishes and for bathing. You will always find a need for hot water in your life.
    Extra heavy duty continuous duty relay that can handle millions
    of cycles at very high amp loads without fusing together or sticking! -
    "Electro mechanical units ours are impervious to lighting, EMP and static electrical discharges"
    "Simple and ultra-reliable" - "A BULLET PROOF SYSTEM"