Battery Charge Controller Wind & Solar THER 48 Volt G5 BRAIN - USA FAST SHIP

Description

You are bidding on one 48V Digital Voltage Meter Test Control Relay Timer Time Delay Switch Module used for battery over charge prevention on all
Comes with fantastic instructions that
are so easy to follow!  Only from a USA seller!
SHIPPED FROM THE USA!
This chip comes with our instructions
(you program it, we make it easy for you)
WARNING: Can tolerate 63 Volts maximum input before failure! Suited for battery regulation only, hence this is why it is called a
battery regulator.
48 Volt model to prevent batteries
and battery banks from over charging
.
no base plate type
DUMP MODE OPERATION ONLY
Large power relay not included
#G5 - 36 and 48 Volt battery controller for wind turbine and solar panels - YouTube
WIND/SOLAR 48 VOLT G5 BATTERY CONTROLLER
WITH BUILT IN DIGITAL DISPLAY
AND INTELLIGENT DUAL
PROCESSOR CONTROLLER -
No micro relay since it uses MOSFETS! Very dependable!
How to wire it up to larger relays;
(With Original "THEM" Thermodyne Controller
.
Says THER on the board. Made with real high voltage rated parts.
Some people claim Thermodyne made but only boards
stamped "THER" are genuine Thermodyne boards)
For solar panels and wind turbines
used in battery changing
Battery regulator for both your wind and solar battery input power.This
regulator can either dump extra power creating free hot water or heater
just cut off extra power to keep your batteries from over charging.This
unit is a must for wind turbine applications as it uses a mechanical
relay which can handle high voltage surges unlike solid state controllers.
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions.  This controller was specially developed for wind turbines and works well on solar too - Get just this one battery controller to do it all! Protect one complete battery bank within power range.
Battery Regulator-
Dump Load Controller-
Diversion Load Regulation-
HOW POWER DRAW DYNAMICS WORKS:
Used to prevent battery over
charging on
Wind -Solar - Hydropower
A battery regulator diverts excess power over to some other useful device when ever your battery is full. Automatically resets and starts over keeping your battery safe.
Use the this excess power to make free hot water or to recharge an auxiliary battery bank, too many uses to mention!
An extremely robust unit! draws almost ZERO power while sensing! 99.998% electrically efficient while sensing!
Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
Diversion load regulator.
Micro processor controlled.
Versatile raised steel mounting plate.
Measures 3.5" long by 2" wide by 1.25" tall.
Works for all Wind Turbines, Solar panels and Hydro.
For all voltages ranges in multiple battery banks.
No grounded IGBT's or MOSFETS -Lighting strike proof isolation.
Electrically efficient. Draws only trace power while
sensing
!
Does not waste electricity while
sensing
in diversion load mode!
DUMP -LOAD
battery controller (dump load and solenoid not included)
The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over charging. Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing cloths or dishes and for bathing. You will always find a need for hot water in your life.
Extra heavy duty continuous duty relay that can handle millions
of cycles at very high amp loads.
"Electromechanical units ours are impervious to lighting, EMP and static electrical discharges"
"Simple and ultra-reliable"- "A BULLET PROOF SYSTEM
User adjustable settings / Few controllers on the market only let you set the voltage level! Max divert mode is 440 amps peak per wind gust / 200 amp peak working load. This is a big hybrid wind and solar charge controller.
Connect multiple turbines and solar panels at the same time!
Use for wind or solar or both at the same time! Use for wind, hydroelectric or solar or both.
We are a THERMODYNE DEALER