Aries warped all right were paying for it Battery charge controller 24V G4 solar

Description

24 Volt model to prevent batteries and battery banks from over charging.
WORKS WITH
CUT MODE OPERATION
or
DUMP MODE OPERATION
Buy 1000 Watt Dump load here
CLICK HERE TO SEE 24V DUMP LOAD
WIND/SOLAR 24 VOLT 440 AMP  DUMP / DISCONNECT CHARGE CONTROLLER
WITH BUILT IN DIGITAL DISPLAY AND INTELLIGENT DUAL PROCESSOR CONTROLLER
(With Original "THEM" Thermodyne Controller
. Says THER on the board. Made with real high voltage rated parts.
Some people claim Thermodyne made but only boards stamped "THER" are genuine Thermodyne boards)
For solar panels and wind turbines used in battery changing
DISCONNECT THE INCOMING POWER.
DIVERT EXCESS POWER
TO A DUMP LOAD.
Use for wind or solar or both at the same time! Also use for hydroelectric or solar or both. User changeable settings -- Several controllers on the market only let you set the dump level!
Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source.
You can connect both wind and solar at the same time. Reverse polarity protection.
Ultra low power consumption even with the volt meter on (almost negligible). You can even set the volt meter to turn off after in-activity.
On board relay- Isolates electronics from back voltage spikes from large 440 amp relay.
This is important to get the longest life out of the electronics. No body else has this!
Dual (2) Microprocessor controlled -- Extremely  stable and very accurate
Multiple user changeable settings, and trip points for many various system requirements and applications- You can change the dump point voltage level,
end of dump voltage level, length of time indivert mode when end dump point voltage is reached
Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board.
Battery Status digital LED - Lets you know your battery's actual voltage in real time!
Green LED come on and then you know it's in dump mode or cut mode depending on how your relay lugs wired.
Plug and Play - Long leads for easy termination to your 24 volt battery or battery bank.
Battery regulator for both your wind and solar battery input power.This
regulator can either dump extra power creating free hot water or heator
just cut off extra power to keep your batteries from over charging.This
unit is a must for wind turbine applications as it uses amechanical
relay which can handle high voltage surges unlike solidstate controllers.
10,000 WATT Rated Secondary Relay
This controller can CUT-OFF incoming power so
NO DUMP LOAD resistor is needed if you do not want to buy one.
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions.  This controller was specially developed for wind turbines and works well on solar too - Get just this one battery controller to do it all!
Worlds Lowest Cost 10,000 Watt
Wind & Solar Controller
Battery Regulator-
Cut/Disconnect Controller-
Diversion Load Regulation-
HOWPOWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses almost no power when it is NOT dumping (energy efficient sensing)
In DISCONNECT mode it draws .2 amps but that's good since that means you have too much power in your batteries anyhow.
Used to prevent battery over
chargingon
Wind -Solar - Hydro
A battery regulator diverts excess power to power
some other useful device when ever your battery is full.
Use the this excess power to make free hot water or to
recharge an auxiliary battery bank, so many uses!
Has push button load tester.
Anextremely robustunit!
draws almost ZERO power while sensing!
99.998% electrically efficient  while sensing!
Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
"Cut" charge controller.
Diversion loadregulator.
Micro processorcontrolled.
Versatile raised steelmounting plate.
Measures10" long by 7" wide by 3" tall.
Works for all WindTurbines, Solar panels andHydro.
For all voltagesranges in multiple batterybanks.
No grounded IGBT's or MOSFETS -Lighting strike proofisolation.
CUT -LOAD
controller (No need to buy a dump load resistor)
Electricallyefficient. Draws only tracepower while
sensing
!
Does not wasteelectricity while
sensing
in  diversion load mode!
HOWPOWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses nopower when it is NOT dumping (energy
efficient
sensing)
The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over -charging.Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing
clothes
or dishes and for bathing. You will always find a need for hot water in your life.
Extraheavy duty continuousduty relay that can handle millions
of cycles at very high amploads without fusing together or sticking! -
"Electromechanical units ours are impervious to
lighting, EMP and static electrical discharges"
"Simple and ultra-reliable"- "A BULLET PROOF SYSTEM"
User adjustable settings / Few controllers on the market only let you set the voltage level! Max solar amperage in divert mode is  440 amps. This is a big hybrid wind and solar charge controller.  Connect multiple turbines and solar panels up to 440 amps worth at the same time!  Use for wind or solar or both at the same time! Use for wind, hydroelectric or solar or both.
Max continuous solar amperage in disconnect mode is 100 amps.
Watch our Free HOW TO video for programming
Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Official Thermodyne Dealer