48 Volt DC / #G5-100 Battery Over-charge Controller solar panel wind turbine O

Description

48 Volt SOLID STATE (MOSFET) Controlled!
Not like other mechanical relay
models with only 50,000 cycles of life
MOSFET's give 10 million cycles +
Open box model - Used for display must be sold as used.
Prevents batteries
and battery
banks from over charging.
CLICK HERE TO SEE 48V / 1000 Watt DUMP LOAD
FOR DUMP MODE OPERATION ONLY
(You will need to buy a water heater or power resistor separately)
#G5 - 36 and 48 Volt battery controller for wind turbine and solar panels - YouTube
WITH BUILT IN DIGITAL DISPLAY
AND INTELLIGENT DUAL
PROCESSOR CONTROLLER - No micro relay since it uses MOSFETS! Very dependable!
(With Original "THEM" Thermodyne Controller
.
Says THER on the board. Made with real high voltage rated parts.
Some people claim Thermodyne made but only boards
stamped "THER" are genuine Thermodyne boards)
For solar panels and wind turbines
used in battery changing
Battery regulator for both your wind and solar battery input power.This
regulator can either dump extra power creating free hot water or heater
just cut off extra power to keep your batteries from over charging.
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions.  This controller was specially developed for wind turbines and works well on solar too - Get just this one battery controller to do it all! Protect one complete battery bank within power range.
MUST BE CONNECTED TO BATTERY AT ALL TIMES!
THE RAW POWER FROM A TURBINE ONLY COULD BURN OUT THE IC CHIP.
THE BATTERY PROTECTS THE CURCUIT FROM HIGH VOLTAGE SPIKES.
WHEN CHANGING OUT BATTERY OR INSTALLING YOUR #G5:
REMOVE THE WIND-TURBINE FOR BATTERY CIRCUIT FIRST.
WHEN INSTALLING HOOK TO YOUR BATTERY FIRST!
WHEN UN-INSTALLING REMOVE FROM BATTERY LAST!
(AVOID VOLTAGES OVER  75 VOLTS!
BEING GROUNDED TO A LEAD ACID BATTERY
WILL BUFFER ALL VOLTAGE DOWN TO 66 VOLTS
SURGE MAX. AND 60 VOLTS NOMINAL)
Battery Regulator-
Dump Load Controller-
Diversion Load Regulation-
HOW POWER DRAW DYNAMICS WORKS:
Used to prevent battery over
charging on
Wind -Solar - Hydropower
A battery regulator diverts excess power to
over to some other useful device when ever your battery is full. Automatically resets and starts over keeping your battery safe.
Use the this excess power to make free hot water or to recharge an auxiliary battery bank, too many uses to mention!
An extremely robust unit! draws almost ZERO power while sensing! 99.998% electrically efficient while sensing!
Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
Diversion load regulator.
Micro processor controlled.
Versatile raised steel mounting plate.
Measures 9" long by 3" wide by 3" tall.
Works best in large multiple battery banks.
Electrically efficient. Draws only trace power while
sensing
!
Works for all Wind Turbines, Solar panels and Hydro
batteries.
No grounded IGBT's or MOSFETS -Lighting strike proof isolation.
Does not waste electricity while
sensing
in diversion load mode!
DUMP -LOAD
battery controller (dump load resistor not included)
The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over charging. Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing cloths or dishes and for bathing. You will always find a need for hot water in your life.
"Electromechanical units ours are impervious to lighting, EMP and static electrical discharges"
"Simple and ultra-reliable"- "A BULLET PROOF SYSTEM
We are a THERMODYNE DEALER