1645 Watt SUPERCORE SC PMA 48 VAC 3 PHASE Wind Turbine Permanent Generator N

Description

This auction is for a
NEW
SUPER-CORE (SC) 3-phase 48VAC PMA designed for use with our 34.64" KT propeller (blades)  and with these
blades can make up to 1645 Watts peak power in high winds (Rated as peak)  This PMA's is recommended for wind turbines only! Peak power reached at about 2000 RPM.
For PMA's / PMG's  for engines and hydro please use our line of #PC1212 or #QC1212 models.
POWER  IN WATTS:
1685 Watts peak / See peak volts for all models below* Make sure your equipment can handle these peaks.Designed to operate in an area with low/medium speed averages of 4.4 to 5.6 m/s and greater (Zone 3-4)Provides 189 kWh per month (2299kWh year)  6.3 kWh per day in a 12.7 mph (5.6 m/s) average wind speed.   In a zone 7 area this turbine can make up to 200% more power or 12.60 kWh.
Wind Zones are defined by m/s
Wind Zone 1      0 – 4.4 m/s
Wind Zone 2    4.4 – 5.1 m/s
Wind Zone 3    5.1 – 5.6 m/s
Wind Zone 4    5.6 – 6.0 m/s
Wind Zone 5    6.0 – 6.4 m/s
Wind Zone 6    6.4 – 7.0 m/s
Wind Zone 7    7.0 – 9.4 m/s  (20-22 mph)
Thermodyne 1600W Wind Turbine Review
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
TREX blades on SC12 PMA Wind Turbine windgeneering
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
What's better, AC or DC wind turbine PMA's / PMG's
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
Thermodnye Hornet Wind Farm
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
You will receive only the most modern magnet core with deep saturation slotted magnets providing deep reaching pole power into the stator coil for maximum amperage.
Includes a real original
SUPER-CORE PMA -
The reason why they cost less
is that they are utilizing an old fashioned
The modern type PLATE AND GROOVE rotor that we have developed is the most celebrated and also the most copied type which we pioneered.  The important part is that PLATE AND GROOVE makes power at MUCH LOWER RPM's than the older and traditional Clam type rotor designs that do not provide deep magnetic saturation of the Stator coil offering 600% more power in low RPM scenarios over Clam type designs
In small wind turbines this is VERY important to make your power in the LOWER RPM ranges.
Spend a little more and get a LOT more  BANG-FOR-YOUR-BUCK!!!  Money well spent!
From the beginning GM designed the Delco to run
WET and even tested them to operate
Under Water
!
Designing an alternator that can survive at 375 degrees F. under the hood of a car operating with rain water coming through the
radiator and from water puddles is
No Easy Task!
Over 100,000,000 10/12si's were produced by Delco and after-market vendors!
Parts for this legendary 'work-horse' will be available for the next 50+ years.  World's most supported and well recognized model!
Our Magnets are on an
angle
We make our own brand new
ROTOR POLE
SHOES
AND
STATOR CORES
!!!
Our PMA's are built from the ground up using only 100% ALL new parts!
(Including the rotor pole shoes and stator coil stacks)
Our
NEW
rotor poles are balanced to within .002 grams for SMOOOOOTH rotation!
MADE IN THE USA!
Get the original
SUPER-Core PLUS+ Design.
Featuring 14 magnetic poles for achieving an amazing 35% power level increase!
Our Magnets are on an
angle
to prevent cogging!