-40%
1 hp 220 VDC Generator permanent magnet build a 12V wind turbine with this model
$ 47.51
- Description
- Size Guide
Description
Manta motor Etek type PMG Permanent Magnet Generator MAKE BUILD ELECTRIC CARS VEHICLES PANCAKE ELECTRIC MOTORS etek ELECTRIC ETEC MOTOR CYCLE PMG Permanent Magnet generator PMA wind turbine hydro power wind turbines mills EtekGREAT FOR
WIND TURBINE PROJECTS
You are bidding on a 1 HP / 208/220/240 volt DC
800 Watt peak electric motor / generator
Very powerful for it's size.
The 220 VDC model is the best for building 12V wind turbines since the shaft speed is the correct ratio for doing this!
Buy this Hub kit:
LINK TO HUB / CLICK HERE
http://www.ebay.com/itm/233587015263
*Also run them on 220 VAC power with the use of a
FULL WAVE RECTIFIER
CLICK HERE TO SEE RECTIFIER
https://youtu.be/PzDN_jmQvzo
Can also be used for powering
electric
karts and bikes.
Can also be used for making Electricity (needs diode)
and changing a battery.
Great for wind or hydro.
Be sure you understand how to set these up for use. LINK HERE!
NOTE:
For wind or hydro power we recommend only our 115 or 208 volt models.
(Use FULL WAVE
RECTIFIER
on the higher voltage models and run them
on AC wall current within their respective voltage groups)
For go karts, mini bikes and cycles we recommend our 12, 24 and 48 volt
models that correspond to your battery bank voltage.
We also sell a 90 volt DC version great for DC water pumps and hydraulic motors
https://youtu.be/PzDN_jmQvzo
Specifications:
Motor length
3.5" diameter / 6" long.
Torque
18 (in lb
f
)
7.5" over all length including shaft
(800W peak)
-
Peak Amps is Watts divided by volts. W ÷ V = A
12mm shaft with 1.75 pitch threads with flat slot at shaft tip.
Shaft is 1.5" long with 3/4" long threaded end (12mm/1.75 pitch thread by 3/4" long)
Two 5/16" extra large mounting holes on the front of the motor.
5/16" NCT mounting holes are 2.874" from center to center (74mm)
3000 rpm / continuous duty at 75% of peak wattage.
Heavy 10 AWG wire to handle the amps.
A put-up and forget design! Expect decades of dependable service life.
Rain, ice and weather resistant electronics in sealed case (not for under water)
Long life graphite brushes.
We sell replacement brushes and bearings.
Works for both CW or CCW rotations.
Epoxy/Lam rotor efficiency = 94.6%
(Brushed motors convert more electricity into usable horsepower)
Weighs ONLY 8.5 lbs. (Almost 100 Watts Per Pound !)
Can be used as a generator, makes power when turned
(Requires 100 amp blocking diode)
THIS IS NOT A 3/4" Diameter SHAFT.
1 hp 220 VDC Generator permanent magnet build a 12V wind turbine with this model
PRODUCT IDEAS
BUILD ELECTRIC CARS / INVENT ELECTRIC BOATS / DESIGN ELECTRIC MOTORCYCLES / MINI BIKES / GO KARTS / POWERED BICYCLES and WIND TURBINEs
PRODUCT IDEAS
BUILD ELECTRIC CARS / INVENT ELECTRIC BOATS / DESIGN ELECTRIC MOTORCYCLES / MINI BIKES / GO KARTS / POWERED BICYCLES
We want you to use these motors in your product designs to help mankind
as we slowly run out of cheap fossil fuels - Electricity is the future.
HOW TO MAKE A TREAD MILL MOTOR WIND TURBINE
Love these blades you were right, wow can they turn on, im getting up to 40
volts out of my indiana general dv pm motor,there scarey sometimes, im
putting it on youtube for all to see, thanks again
-uptick57
wind generator homemade - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
https://youtu.be/WCkpjHPna-Y